Integrate Molex 4pin, SATA and 6-pin PCI-E power interface on PCB for direct connection to your power supply ,reduces the power burden on your motherboard and ensures maximum compatibility with your power supply.
#4 pin molex connector on motherboard free
Thin and fast USB 3.0 cable available to connect PCI-E 1X and PCI-E 16X sides for more free installation and faster data transfer for graphics card. Multiple Voltage Regulation Components (Voltage Regulating Diode and Linear Regulator) Overcurrent Protection (Surface Mounted Fuse) to safeguard your components in the event of a short circuit.
4 High Quality Solid Capacitors for stable and safe power delivery. Specifications: The perfect solution for setting up Ethereum mining rigs, whether small open air rigs or large rack based miners.Also, Molex's website has a pretty decent search tool with lots of parts data.(1) PCI Express PCI-e 1X to 16X Mining Riser Card Cable, USB 3.0 Bitcoin Miner Machine X16 to PCI e Mining ETH GPU Riser Adapter Power by SATA, Molex 4pin, 6pin It's not in the Mouser paper catalog, but both sites have the datasheets available. Mouser and Digi-Key both carry these, so it may be a decent starting point. Thus, 5240-041 is a four-position, w/o ear. 5240 is the SPOX male wire-to-wire housing, -03 is three position, and the 1 suffix denotes w/o mounting ear. The "old" part number for these is 5240-031, respectively. When doing a little research, I see that 29-11-0033 is the same thing without panel mount ears.The motherboard has some 14-pin SCSI power connectors that plug into the backplane, a bunch of 6-pin fan connectors, and a single 4-pin male. These housings have panel mount ears, but they can be cut off pretty easily with an x-acto knife.* The drives have both SATA and 4-pin Molex connectors. The keying is correct for 4 pin and so is the 3 pin, so they will work in an exact fit but not a universal fit. These housings are not dual-keyed for 3 and 4 pin.This isn't really an issue with 4-position connectors. The 29-11-0032 is a 4-pin connector that we use in short jumpers connect hot-swap fans to the motherboard fan headers. The only name brand I could find is a Molex SPOX connector. There are several of these housings out there, most of which are off-brand. All of these wires attach to a four pin connection on the motherboard. 3/4pins are about half the size of a molex. Today, the connector is a standard power connector and is used with both Intel and AMD motherboards. A molex shouldnt look similar to a 3/4 pin connector. The Molex part number of the header is 47053-1000. The P4 connector is a 12V power supply cable used with motherboards that have an Intel Pentium 4 or later processor. The Molex part number of individual crimp contacts is 08-50-0114. The Molex part number of receptacle is 47054-1000. These can be plugged into 3-pin headers, but will lose their fan speed control. The additional pin is used for a pulse-width modulation signal to provide variable speed control. This is a special variant of the Molex KK connector with four pins but with the locking/polarisation features of a three-pin connector. The matching PCB header Molex part number is 22-23-2031.
The Molex part number of the individual crimp contacts is 08-50-0114. The Molex part number of receptacle is 22-01-3037. The three pins are used for ground, +12 V power, and a tachometer signal. Pins are square and on a 0.1 inch (2.54 mm) pitch.
It is a small, thick, rectangular in-line female connector with two polarizing tabs on the outer-most edge of one long side. This Molex connector is used when connecting a fan to the motherboard or other circuit board. Direct quote from wikipedia: "computer_fan"
0 kommentar(er)
